|
|
This product is currently out of stock.
Instructions for Receiving Channels on New Satellite Galaxy19
3ABN, 3ABN Latino, LLBN, Hope Channel, Esperanza TV, Radio74 and LifeTalk Radio Move
Updated 12/27/2011
3ABN, 3ABN Latino, LLBN, Hope Channel, Esperanza TV, Radio 74 and LifeTalk Radio networks are moving to a new satellite. New Adventist channels Channels Amazing Facts, 3ABN Proclaim, LLBN Arabic, LLBN Chinese, Amazing Discoveries and Smart Lifestyle TV have already begun broadcasting! 3ABN Dare 2 Dream Network Launches Jan 02, 2012. Additional Adventist channels will soon be available.
If you have a Glorystar satellite dish with two LNBFs installed, no dish move or re-aiming is needed. GEOSATpro DVR1100c, DSR100c and DSR200c receivers will automatically add these new channels when installed on a Glorystar system. Fortec Star Mercury II and GEOSATpro DVR1000ci receivers need to be manually updated using the instructions below.
To contract a local installer to assist with the satellite dish move and receiver programming, please visit a free satellite installer referral service online at http://www.FTAinstall.com
We highly recommend the purchase of a complete Glorystar system or upgrade your old receiver with a new Glorystar receiver. Glorystar receivers have all channel changes in place and will automatically update and add new channels as they become available. Please call us at 866-598-8728 and ask the sales team for a Glorystar system or receiver upgrade to watch all the current channels and automatically add any new Glorystar channels.
New Satellite Parameters
New Satellite: Galaxy 19
Transponder Frequencies: 11842 and 12060
Polarity: Horizontal
Symbol Rate: 22000
Note: The Galaxy 19 satellite has had several names through the years. This satellite may be listed in your receiver as: Telstar 5, T5, Intelsat America 5, IA5, Galaxy 25, G25, Galaxy 19 or G19.Other channels are available on the satellites. If you have a GEOSATpro DVR1100c, DSR100c or 200c receiver, these Christian channels will be automatically updated each week. If you own a different brand receiver and wish to add these channels to your system, please follow this link Glorystar Channels to view a channel list. Substitute the posted Transponder Frequency, Polarity and Symbol Rate parameters from this list, then scan the channels into your receiver.
To view the free online programming and aiming instructions, click on your receiver model from the list below:
Receiver Brand: GEOSATpro
DVR1100c / DSR100c/200c - Instructions
Glorystar System
Video Assistance
|
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
GEOSATpro DVR1100c / DSR100c/200c receivers automatically update from the satellite and no manual channel programming is necessary.
If you are not receiving the new channels or new channels are not automatically added to your receiver, verify that the Signal Quality (Q) reading on 3ABN (channel 106) is at least 50% and you are seeing television programming. If the Signal Quality is not at least 50%, the dish will need to be adjusted to increase the Signal Quality (Q) reading.
To perform a Manual Update:
Using your GEOSATpro remote control, press Menu button
Left Arrow to Accessory Screen
Down Arrow to OTA
Press OK
Verify Automatic Update setting is ON
(if OFF, Press Right Arrow to ON)
Press Down Arrow to Update Now
Press OK
Screen displays" Do you want to update S/W?"
Press OK
After OTA update, the receiver will restart.
Press Menu button
Press VOL up button (the button that points to the right) three times to “UTILITY” menu
Press the Channel up button (the button that points to the up) to highlight “FACTORY DEFAULT”
Press OK button to display “ARE YOU SURE TO LOAD FACTORY DEFAULT?”
Press OK button to restart the receiver.
Press OK to select ENGLISH
Press OK to select GLORYSTAR
Press OK to select correct “TIMEZONE” then press OK
Press VOL up button to set “DAYLIGHT SAVINGS” ON or OFF
Press the Channel down button to highlight “NEXT”
Press OK button to display “CONNECT COAX CABLE” screen
Verify Signal Quality reading of at least 50% on 3ABN (channel 106) and on Cornerstone (channel 113)
Press orange Signal button to remove signal quality meter
The receiver date and time is automatically set by the satellite. Place the receiver on Channel 1 for at least 15 seconds to update
Note: Failure to have Signal Quality of at least 50% and displaying television programming on 3ABN (channel 106) will prevent the receiver from automatically updating and adding new channels.
Watch Receiver Programming Video
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
1. Using your Manhattan DSR 1500 remote control
press “SETUP” button (located above the #3 button)
2. Press *down arrow and highlight “SYSTEM SETTING”
3. Press OK button
4. Press *down arrow and highlight “DEFAULT SETTING”
5. Press OK button and the screen will display “WARNING:
THIS WILL RESET ALL SETTINGS TO DEFAULT VALUES”
6. Press *right arrow to select “OK”
7. Press OK button and the screen will display “WARNING:
ARE YOU SURE YOU WANT TO CONTINUE”
8. Press *right arrow to select “OK”
9. Press OK button
10. Screen will Display “PLEASE WAIT” then “STORED SETTINGS RESET TO DEFAULT”, press OK button to restart the receiver.
11. Screen displays LANGUAGE SELECTION, press OK button.
12. Press *down arrow to “TP FREQUENCY”
13. Using the number buttons on the remote control enter the numbers 11842
14. Press *down arrow to select POLARIZATION should be “HOR”
15. Press *down arrow to ‘SYMBOL RATE”
16. Using the number buttons on the remote control enter the numbers 22000
17. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. Move dish back and forth very slowly until you get the highest reading on the yellow Signal Strength bar.
18. You may have to adjust the elevation to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, slightly raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, slightly lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle. Once the Signal Strength bar is at the highest reading, tighten the dish mounting and elevation.
19. Slightly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the Signal Strength bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com
20. When you have the maximum yellow/green bar on “Signal Strength”, press *down arrow to “Start Search” (there will be quotation marks “” on either end of Start Search when it is selected)
21. Press the OK button
22. A box will pop up to the right. When you see the word “Store” at the bottom of that box press OK button
23. Screen will display “CHANNEL DATA IS BEING UPDATED” then return to a TV viewing screen.
*DIRECTIONAL ARROWS ON THE REMOTE CONTROLS ARE THE “CHANNEL UP BUTTON (UP ARROW), CHANNEL DOWN BUTTON (DOWN ARROW), VOLUME UP BUTTON (RIGHT ARROW), VOLUME DOWN BUTTON (LEFT ARROW)
Video Assistance - Dish Aiming & Receiver Programming
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
1. Using your Manhattan SKYLINE 1000 remote control
press the “MENU” button
2. Press the *down arrow to highlight “Master Reset”
3. Press the OK button two (2) times and the screen will display “Resetting - Please Wait”
4. Press ESC button to exit “OSD SETUP”
5. Press ESC button to exit “TV SETTINGS”
6. Press ESC button to exit “TIME SETTINGS” (or enter time settings and select STORE and press OK)
7. Press ESC button to exit “ANTENNA SETTINGS”
8. Press *down arrow to highlight “Search Mode”
9. Press *left arrow to select “Manual FTA”
10. Press the channel down button to highlight “TP DATA”
11. Press OK button
12. A box will pop up to the right. At the top of that box, in yellow, make sure it says “TP1:3ABN”, if not, push the *left or right arrow to get to “TP1:3ABN”
13. Press *down arrow to “FREQ” (frequency)
14. Using the number buttons on the remote control enter the numbers 11842
15. Press *down arrow to “Polarity”
16. Press *left arrow to select “HORZ.”
17. Press *down arrow to “S/R” (symbol rate)
18. Using the number buttons on the remote control enter the numbers 22000
19. Press *down arrow to “FEC”
20. Press *left arrow to select ¾
21. Press *down arrow to “STORE”
22. Press OK button and screen will display “Storing Data – Please Wait”
23. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. When you are on the satellite you will get two green bars, one on signal and one on quality. Move dish back and forth very slowly until you get the highest reading on the green Quality bar.
24. You may have to adjust the elevation to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, slightly raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, slightly lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle. Once the green Quality bar is at the highest reading, tighten the dish mounting and elevation.
25. Slighly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the green Quality bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com
26. Press Channel down button to “START”
27. Press OK button and upon channel scan completion the screen will display “Resetting – Please Wait”
28. Press OK button to continue
*DIRECTIONAL ARROWS ON THE REMOTE CONTROLS ARE THE “CHANNEL UP BUTTON (UP ARROW), CHANNEL DOWN BUTTON (DOWN ARROW), VOLUME UP BUTTON (RIGHT ARROW), VOLUME DOWN BUTTON (LEFT ARROW)
Video Assistance - Dish Aiming & Receiver Programming
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
1. Using your Topfield 3000Fi remote control
press the “MENU” button
2. Press *down arrow to highlight “Installation”
3. Press OK button
4. Press *down arrow to select “Factory Setting”
5. Press OK button to display “Reset All Data”
6. Press *left arrow to select “Yes”
7. Press OK button to display “Position Data Delete”
8. Press *left arrow to select “Yes”
9. Press OK button to continue
10. Press *up arrow to select “SAT/TP Edit”
11. Press OK button again on “Satellite Name” (A box with a list of satellite names will pop up on the right hand side)
12. Press *down arrow to select “Telestar5(KU)” or “Intel_Amc5(KU)”
13. Press OK button
14. Press *down arrow to select “Add new TP”
15. Press OK button to display new window “Add New TP – “Frequency” will be highlighted in white.
16. Using the number buttons on the remote control enter the numbers 11842
17. Press *down arrow to select “Symbol Rate”
18. With the number buttons on the remote control enter the numbers 22000
19. Press *down arrow to select “Polarization” and push the *right arrow one time and it should read “Horizontal”
20. Press *down arrow to the word “OK” and press the OK button on the remote control.
21. Press *down arrow to select “Channel Search” and press the OK button on the remote control.
22. In the lower right hand corner you will see two bars, one says “Level” and one says “Quality”. You should have a green “Level” bar
23. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. When you are on the satellite you will get a yellow bar on the bar that says “Quality”. Move dish back and forth very slowly until you get the highest reading on the yellow “Quality” bar.
24. You may have to adjust the elevation (up/down) to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, slightly raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, slightly lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle. Once the yellow “Quality” bar is at the highest reading, tighten the dish mounting and elevation.
25. Slightly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the yellow “Quality” bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com
26. Once you have the yellow “Quality” bar with the highest strength, press OK button to enter the “Channel Search” screen.
27. Press Channel down button to select “Search Mode” and press the Volume up button (the button that points to the right) one time and it should read “Manual”.
28. Press Channel down button to select “FTA/Scrambled” and press the Volume up button (the button that points to the right) one time and it should read “FTA Only”.
29. Press Channel down button to select “Start Search”
30. Press OK button and a “Searching” screen will appear.
31. When Channel Scan is completed press OK, the Channel Search Screen will appear.
32. Press OK to continue.
32. Press Exit button to exit the menus and view the new programming.
*DIRECTIONAL ARROWS ON THE REMOTE CONTROLS ARE THE “CHANNEL UP BUTTON (UP ARROW), CHANNEL DOWN BUTTON (DOWN ARROW), VOLUME UP BUTTON (RIGHT ARROW), VOLUME DOWN BUTTON (LEFT ARROW)
Video Assistance - Dish Aiming - Receiver Programming
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
1. Using your Topfield 4000 / 6200 remote control
press the “MENU” button
2. Press *down arrow to highlight “Installation”
3. Press OK button
4. Press *down arrow to select “Factory Setting”
5. Press OK button to display “Reset All Data”
6. Press *left arrow to select “Yes”
7. Press OK button to display “Position Data Delete”
8. Press *left arrow to select “Yes”
9. Press OK button to continue
10. Press *up arrow to select “SAT/TP Edit”
11. Press OK button again on “Satellite Name” (A box with a list of satellite names will pop up on the right hand side)
12. Press *down arrow to select “Intel_Amer5(KU)”
13. Press OK button
14. Press *down arrow to select “Add new TP”
15. Press OK button to display new window “Add New TP – “Frequency” will be highlighted in white.
16. Using the number buttons on the remote control enter the numbers 11842
17. Press *down arrow to select “Symbol Rate”
18. With the number buttons on the remote control enter the numbers 22000
19. Press *down arrow to select “Polarization” and push the *right arrow one time and it should read “Horizontal”
20. Press *down arrow to the word “OK” and press the OK button on the remote control.
21. Press *down arrow to select “Service Search” and press the OK button on the remote control.
22. In the lower right hand corner you will see two bars, one says “Level” and one says “Quality”. You should have a green “Level” bar
23. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. When you are on the satellite you will get a yellow bar on the bar that says “Quality”. Move dish back and forth very slowly until you get the highest reading on the yellow “Quality” bar.
24. You may have to adjust the elevation (up/down) to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, slightly raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, slightly lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle. Once the “Quality” bar is at the highest reading, tighten the dish mounting and elevation.
25. Slightly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the “Quality” bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com
26. Once you have the yellow “Quality” bar with the highest strength, press OK button to enter the “Channel Search” screen.
27. Press Channel down to select “Search Mode” and press the Volume up button (the button that points to the right) one time and it should read “Manual”.
28. Press Channel down to select “FTA/Scrambled” and push the Volume up button (the button that points to the right) one time and it should read “FTA Only”.
29. Press Channel down to select “Start Search”
30. Press OK and a “Searching” screen will appear.
31. When Channel Scan is completed press OK, the Channel Search Screen will appear.
32. Press OK to continue.
32. Press Exit button to exit the menus and view the new programming.
*DIRECTIONAL ARROWS ON THE REMOTE CONTROLS ARE THE “CHANNEL UP BUTTON (UP ARROW), CHANNEL DOWN BUTTON (DOWN ARROW), VOLUME UP BUTTON (RIGHT ARROW), VOLUME DOWN BUTTON (LEFT ARROW)
Video Assistance - Dish Aiming & Receiver Programming
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
Fortec Star Mercury II - Glorystar Two LNBF sytem.
1. Tune your Fortec Star Mercury II receiver on TBN (Channel 2) and verify that programming is showing.
If programming is not showing on TBN (Channel 2) troubleshooting will be necessary before continuing this process.
2. Using your Fortec Star Mercury II remote control press “Menu” button to go to "Installation" screen and “ANTENNA SETUP” highlighted yellow.
3. Press the Channel down button twice to highlight “TP SCAN”
4. Press OK button to go to “TP SCAN” screen
5. Press the Channel down button to highlight “FREQUENCY”
6. Using the number buttons on the remote control enter 11842
7. Press Channel down button to highlight “POLARITY” and push the Volume up button (the button that points to the right) it should display “Horizontal”
8. Press Channel down to “SYMBOLRATE”
9. Using the number buttons on the remote control enter the numbers 22000
10. On the bottom of the screen you will see two bars, one says “SIGNAL LEVEL” and the other “SIGNAL QUALITY”. If the dish has been properly installed the Signal Quality reading will be at least 50%. If not, troubleshooting will be necessary before continuing this process. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com.
11. Once you have the “Signal Quality” bar with the highest strength (at least 50%), press Yellow button to begin scan.
12. When Channel Scan is completed, pop up window displaying "Do you want to save?" with "Yes" highlighted Yellow.
13. Press OK button to save. Programming will automatically be displayed.
14. Please, note that the new channels will be on higher channel numbers.
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
Fortec Star Mercury II - One LNBF sytem.
1. Using your Fortec Star Mercury II remote control press “Menu” button to go to "Installation" screen and highlight “ANTENNA SETUP”
2. Press the Channel down button to highlight “Factory Reset”
3. Press OK button to go to “Factory Reset” screen with Factory Reset line highlighted.
4. Press OK button. A pop up window displaying "Are You Sure?" with "No" highlighted Yellow.
5. Press VOL down button to highlight "Yes" with yellow.
6. Press OK button.
7. When Language screen appears, turn off master power switch on back of receiver or unplug receiver from AC power outlet for 10 seconds.
8. Turn the receiver back on or plug the receiver back into AC power outlet. "Language" Menu will appear.
9. Press "Menu" to go to "Installation" screen with “Antenna Setup” highlighted.
10. Press OK button to enter "Antenna Setup" screen.
11. If needed, press VOL down button (the button that points left) to select "Galaxy25 Ku 97.0W or IA5/KU 97.0W"
12. Press the Channel down button to highlight “LNB TYPE”
13. Press VOL up button to display “LNB-10750”
14. Press Menu button to go back to “INSTALLATION” screen
15. Press the Channel down button twice to highlight “TP SCAN”
16. Press OK button to go to “TP SCAN” screen
17. Press the Channel down button to highlight “FREQUENCY”
18. Using the numbers buttons on the remote control enter 11842
19. Press Channel down button to highlight “POLARITY” and push the Volume up button (the button that points to the right) it should display “Horizontal”
20. Press Channel down to “SYMBOLRATE”
21. With the number buttons on the remote control enter the numbers 22000
22. On the bottom of the screen you will see two bars, one says “SIGNAL LEVEL” and the other “SIGNAL QUALITY”.
23. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. When you are on the satellite you will get a blue indicator on the bar that says “Quality”. Move dish back and forth very slowly until you get the highest reading on the “Quality” bar.
24. You may have to adjust the elevation (up/down) to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle and adjust. Once the“Quality” bar is at the highest reading, tighten the dish mounting and elevation.
25. Slightly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the green “Quality” bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com.
26. Once you have the “Signal Quality” bar with the highest strength (at least 50%), press Yellow button.
27. When Channel Scan is completed, pop up window displaying "Do you want to save?" with "Yes" highlighted Yellow.
28. Press OK button to save. Programming will automatically be displayed.
Video Assistance - Dish Aiming & Receiver Programming
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
Fortec Star Lifetime Ultra
1. Using your Fortec Star Lifetime Ultra remote control push “Menu” button
2. Press VOL up button (the button that points to the right) to select “CHANNEL EDIT”
3. Press OK button
4. Press the Channel down button (the button that points down) to highlight “DELETE”
5. Press OK button
6. Press VOL up button to “ALL CH”
7. Press OK three times and a window will pop up on the screen displaying “NO CHANNEL DATA”
8. Press VOL up button (the button that points to the right) to “INSTALLATION” screen with "Antenna Setup" highlighted.
9. Press OK button to enter the Antenna Setup screen
10. Press Channel up button to highlight “IA5/Ku 97.0W”
11. Press OK button to highlight "LNB type"
12. Press VOL up button to display “Standard”
13. Press EXIT button and a window will pop up on the screen displaying "INFO - Press ok to save or EXIT"
14. Press OK button to save
15. Press EXIT button to enter the Installation Screen with Antenna Setup highlighted
16. Press Channel up button to highlight “Advanced Scan”
17. Press OK button and a window will pop up on the screen “FTA”
18. Press OK button to edit the "Selected Satellite" window
19. If needed, press the Channel down button (the button that points down) to highlight “IA5/Ku 97.0W”
20. Press OK button to enter the “ADVANCED SCAN” screen and “DOWN FREQUENCY” will be highlighted
21. Using the numbers buttons on the remote control enter the numbers 11842
22. Press Channel down to “Symbol Rate”
23. With the number buttons on the remote control enter the numbers 22000
24. Press Channel down to “Polarity” and push the Volume up button (the button that points to the right) one time and it should read “Horizontal”
25. In the right hand side of the screen you will see two bars, one says “Level” and one says “Quality”. You should have a green “Level” bar (over 50%).
26. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. When you are on the satellite you will get yellow then green bar on the bar that says “Quality”. Move dish back and forth very slowly until you get the highest reading on the “Quality” bar.
27. You may have to adjust the elevation (up/down) to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, slightly raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, slightly lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle. Once the “Quality” bar is at the highest reading, tighten the dish mounting and elevation.
28. Slightly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the “Quality” bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com.
29. Once you have the green “Quality” bar with the highest strength (over 50%), press OK button to enter the “Channel Search” screen.
30. When Channel Scan is completed, programming will automatically be displayed.
Video Assistance - Dish Aining & Receiver Programming
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
GEOSATpro 1000ci - Glorystar 2 LNBF sytem.
1. Using your GEOSATpro DVR1000ci remote control place the receiver on the 3ABN channel
2. Press “Menu” button
3. Press the Channel down button (the button that points down) to highlight “INSTALLATION”
4. Press OK button to go to “PASSWORD” screen
5. Using the numbers buttons on the remote control enter 0000
6. Press the Channel down button to highlight “TP EDIT / SCAN”
7. Press OK button to display the “TP EDIT / SCAN” screen.
8. Press the Channel down button to highlight “TP DELETE” (verify TP frequency is 11822)
9. Press OK button and a window will pop up displaying “DO YOU WANT TO DELETE THIS TP?”
10. Press OK button
11. Verify TP frequency is now 11983. Press OK button and a window will pop up displaying “DO YOU WANT TO DELETE THIS TP?”
12. Press OK button
13. Verify TP frequency is now 12020. Press OK button and a window will pop up displaying “DO YOU WANT TO DELETE THIS TP?”
14. Press OK button
15. Press the Channel down button to highlight “SATELLTE NAME”
16. Press VOL up button (the button that points to the right) repeatedly until “IA-5/KU” is displayed
17. Press the Channel down button to highlight “TP FREQUENCY”
18. Using the numbers buttons on the remote control enter 11842
19. If necessary, press Channel down button to highlight “POLARIZATION” and press the VOL up button (the button that points to the right) it should display “Horizontal”
20. Press Channel down to “SYMBOL RATE”
21. With the number buttons on the remote control enter the numbers 22000
22. Press Channel down button to highlight “Scan” and push the VOL up button until “FREE ONLY” is displayed.
23. On the left side of the screen you will see a “SIGNAL QUALITY” strength indication bar. If the Glorystar “Dual LNBF” dish is correctly installed a level of at least 30% should be displayed. If not, troubleshooting will be necessary before continuing this process. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com.
24. Once you have the signal quality bar with the highest strength, press OK button to enter the “CHANNEL SCANNING” screen.
25. When Channel Scan is completed, press Channel up or down button to highlight “3ABN” and press OK to view programming.
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
GEOSATpro 1000ci - 1 LNBF sytem.
1. Using your GEOSATpro remote control place the receiver on the 3ABN channel
2. Press “Menu” button
3. Press the Channel down button (the button that points down) to highlight “INSTALLATION”
4. Press OK button to go to “PASSWORD” screen
5. Using the numbers buttons on the remote control enter 0000
6. Press the Channel down button to highlight “TP EDIT / SCAN”
7. Press OK button to display the “TP EDIT / SCAN” screen.
8. Press the Channel down button to highlight “TP DELETE” (verify TP frequency is 11822)
9. Press OK button and a window will pop up displaying “DO YOU WANT TO DELETE THIS TP?”
10. Press OK button
11. Verify TP frequency is now 11983. Press OK button and a window will pop up displaying “DO YOU WANT TO DELETE THIS TP?”
12. Press OK button
13. Verify TP frequency is now 12020. Press OK button and a window will pop up displaying “DO YOU WANT TO DELETE THIS TP?”
14. Press OK button
15. Press the Channel down button to highlight “SATELLTE NAME”
16. Press VOL up button (the button that points to the right) repeatedly until “IA-5/KU” is displayed
17. Press the Channel down button to highlight “TP FREQUENCY”
18. Using the numbers buttons on the remote control enter 11842
19. If necessary, press Channel down button to highlight “POLARIZATION” and press the VOL up button (the button that points to the right) it should display “Horizontal”
20. Press Channel down to “SYMBOL RATE”
21. With the number buttons on the remote control enter the numbers 22000
22. Press Channel down button to highlight “Scan” and push the VOL up button until “FREE ONLY” is displayed.
23. On the left side of the screen you will see a “SIGNAL QUALITY” strength indication bar. 10% reading indicates the dish is not yet aimed and this level will increases up to 98% on the strongest signals.
24. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. When you are on the satellite you will get a level above 10% on the signal quality bar. Move dish back and forth very slowly until you get the highest reading.
25. You may have to adjust the elevation (up/down) to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle and adjust. Once the signal quality bar is at the highest reading, tighten the dish mounting and elevation.
26. Slightly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the signal quality bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com.
27. Once you have the signal quality bar with the highest strength, press OK button to enter the “CHANNEL SCANNING” screen.
28. When Channel Scan is completed, press Channel up or down button to highlight “3ABN” and press OK to view programming.
Video Assistance - Dish Aiming & Receiver Programming
Important Notice: Your FREE online re-aiming instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment.
If you require additional assistance for this re-aiming, please contact the company or broadcaster where you originally purchased your satellite system.
1. Place the BEC 1000 / 2000 satellite receiver on Channel 1
2. Using the remote control press the “MENU” button to display the "Channel List" screen
3. Press Right Arrow button to display "Channel Edit" screen with the TV icon highlighted
4. Press Enter button to display the “TV CH Edit” screen
5. Press Enter button to place a "X" to the left of the channel name
6. Press Down Arrow button to highlight the next channel name
7. Press Enter button to place a "X" to the left of the channel name
8. Repeat steps 6 and 7 until all channels have a "X" beside the channel name
9. Press Menu button to display a pop up window
10. Press Down Arrow 2 times to highlight "Delete"
11. Press Enter button
12. Press Return button to display the "Channel Edit" screen
13. Press Right Arrow button to display "Setup" screen with "CH Search" highlighted
14. Press Enter button to display "Channel Search" screen with "Satellite" highlighted
15. Press Down Arrow button to highlight "Frequency"
16. Using the numeric keypad, enter 11842
17. Press Down Arrow button to highlight "Symbol Rate"
18. Using the numeric keypad, enter 22000
19. Press Down Arrow button to highlight "Polarization"
20. Press Enter button to select "Horizontal"
21. Press *down arrow to “STORE”
22. Go outside to the dish. Mark the current position of the dish on the mast pipe and the current elevation angle.
Slightly loosen the bolts that secure the dish to the vertical mast pipe, move the satellite dish slightly to the left. Have someone else inside looking at the TV screen. When you are on the satellite you will get two bars, one on signal and one on quality. Move dish back and forth very slowly until you get the highest reading on the Quality bar.
23. You may have to adjust the elevation to receive the new satellite. If you are in the central US or Canada, minimal or no elevation change will be necessary. If you are in the eastern part of the US or Canada, slightly raise the dish approximately 2 degrees. If you are in the western part of the US or Canada, slightly lower the dish approximately 2 degrees. Slightly loosen the bolts that lock the elevation angle. Once the Quality bar is at the highest reading, tighten the dish mounting and elevation.
24. Slighly loosen the screws of the clamp that holds the LNBF. Slowly rotate the LNBF clockwise or counter clockwise to peak the Quality bar. If you or an installer need the exact aiming coordinates for the satellite, please visit website http://www.GeoSatFinder.com
25. Press Down Arrow button to “Scan”
26. Press Enter button to scan for new channels. When the scan is completed a popup window appears " Scan Message: Scan Complete"
27. Press Return button 3 times to display a popup window "Confirm Save" with "OK" highlighted
28. Press Enter button. The receiver will restart and the new channels will be added to your channel list/ Please note that the satellite name will be displayed as AMC4, but it really has been changed to the new satellite Galaxy 19.
If your receiver is not listed here, please follow the instructions provided with your receiver on how to scan additional channels. Indicate the following:
Transponder Frequency: 11842,
Polarity: Horizontal
Signal Bit Rate: 22000 Now, scan in the new channels.
If you would like to own a Glorystar receiver that updates automatically (so there is no need to do these steps for new or moved channels in the future), please call us at 866-598-8728 and ask the sales team for a Glorystar receiver to watch all the new and current Christian Channels including 3ABN, LLBN, Hope Channels as well as all new Adventist Channels.
|
Receiver Brand: Manhattan
DSR 1500 - Instructions
1 LNBF System
Video Assistance |
Receiver Brand: Manhattan
SKYLINE 1000 - Instructions
1 LNBF System
Video Assistance |
Receiver Brand: Topfield
3000Fi - Instructions
1 LNBF System
Video Assistance |
Receiver Brand: Topfield
4000/6200 - Instructions
1 LNBF System
Video Assistance |
Receiver Brand: Fortec Star
Mercury II - Instructions
Glorystar 2 LNBF System |
Receiver Brand: Fortec Star
Mercury II - Instructions
1 LNBF System
Video Assistance |
Receiver Brand: Fortec Star
Lifetime Ultra - Instructions
1 LNBF System
Video Assistance |
Receiver Brand: GEOSATpro
DVR1000ci - Instructions
Glorystar 2 LNBF System |
Receiver Brand: GEOSATpro
DVR1000ci - Instructions
1 LNBF System
Video Assistance |
Receiver Brand: BEC
1000 / 2000 - Instructions
1 LNBF System
|
Other receivers
|
|
|
US STORE - switch to 
CANADA
Home
Adding to cart....
Added to cart!